Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
anyone make their......
Author Message
MonsterStepDad Offline
Member
***

Posts: 55
Likes Given: 0
Likes Received: 23 in 14 posts
Joined: Jan 2018
Reputation: 0
Post: #1
anyone make their......
Anyone made their own mod? thinking of building a mod for variable wattage.

any info or ideas very happy to hear.
10-05-2018 09:38 PM
Find all posts by this user Like Post Quote this message in a reply
gentlydoingit* Offline
TVF FreeCycle Manager
******
FreeCycle Manager

Posts: 6,189
Likes Given: 7,378
Likes Received: 9,637 in 4,260 posts
Joined: Nov 2015
Reputation: 191
Post: #2
RE: anyone make their......
I've made a few In here 

Variable wattage requires a premade chip, as making your own buck converter is a massive ball-ache. Pwm is much easier and cheaper with some pretty good results.
What are you thinking of making?

Don't forget to apply for the freecycle section!
http://www.thevapingforum.com/Forum-FreeCycle--191
10-05-2018 11:36 PM
Find all posts by this user Like Post Quote this message in a reply
[-] The following 4 users Like gentlydoingit*'s post:
DaleJr (05-11-2018), Don (05-11-2018), Fatboy (05-11-2018), TinWhisker (05-11-2018)
steelcity7476 Offline
Junior Member
**

Posts: 1
Likes Given: 0
Likes Received: 0 in 0 posts
Joined: May 2018
Reputation: 0
Post: #3
Is my tank ok to use
I had my mod In my pocket and pulled it out of my pocket to hit it. I didn't notice that there was a paper clip in the air flow chamber. It fried my mod. The tank is a fireluke mesh tank and coil. My mod is covered under warranty so they are sending me a new one. Would the tank be ok to use with a new coil in it. I'm new to using mods. Please Help!
11-05-2018 03:10 PM
Find all posts by this user Like Post Quote this message in a reply
gentlydoingit* Offline
TVF FreeCycle Manager
******
FreeCycle Manager

Posts: 6,189
Likes Given: 7,378
Likes Received: 9,637 in 4,260 posts
Joined: Nov 2015
Reputation: 191
Post: #4
RE: anyone make their......
If it fried yout mod it means the hard short pulled serious amperage! You'll need to check the insulation between the 510+ pin and the body of the atty, stands a chance it could be melted. 

Don't forget to apply for the freecycle section!
http://www.thevapingforum.com/Forum-FreeCycle--191
11-05-2018 03:56 PM
Find all posts by this user Like Post Quote this message in a reply
[-] The following 3 users Like gentlydoingit*'s post:
Don (05-12-2018), ecignut (05-11-2018), LilFracker (05-12-2018)
MonsterStepDad Offline
Member
***

Posts: 55
Likes Given: 0
Likes Received: 23 in 14 posts
Joined: Jan 2018
Reputation: 0
Post: #5
RE: anyone make their......
looking at making my own pcb's as dont want to use another manufacturers. fairly good at building micro pcb's but its the firmware/software that i will struggle with.
15-05-2018 11:55 AM
Find all posts by this user Like Post Quote this message in a reply
[-] The following 1 user Likes MonsterStepDad's post:
gentlydoingit* (05-15-2018)
gentlydoingit* Offline
TVF FreeCycle Manager
******
FreeCycle Manager

Posts: 6,189
Likes Given: 7,378
Likes Received: 9,637 in 4,260 posts
Joined: Nov 2015
Reputation: 191
Post: #6
RE: anyone make their......
Not kidding! It's conceivable to use passive resistive/capacitive controlled ic's and a digi pot, pic's eproms etc are way beyond my abilities. 

I'd be very interested to see what you come up with Good

Don't forget to apply for the freecycle section!
http://www.thevapingforum.com/Forum-FreeCycle--191
15-05-2018 12:29 PM
Find all posts by this user Like Post Quote this message in a reply
ecignut Offline
Squonk and Toodle Club Member
*******
Senior Staff

Posts: 11,460
Likes Given: 16,354
Likes Received: 19,013 in 8,977 posts
Joined: Apr 2015
Reputation: 214
Post: #7
RE: anyone make their......
(15-05-2018 12:29 PM)gentlydoingit* Wrote:  Not kidding! It's conceivable to use passive resistive/capacitive controlled ic's and a digi pot, pic's eproms etc are way beyond my abilities. 

I'd be very interested to see what you come up with Good
I would be extremely interested as well - if I knew what the hell you were talking about[Image: tongue.gif].
15-05-2018 03:51 PM
Find all posts by this user Like Post Quote this message in a reply
[-] The following 1 user Likes ecignut's post:
gentlydoingit* (05-15-2018)
Post Reply