What have you got on order ?

[Robjenko]

(19-12-2017 04:11 PM)ecignut Wrote:  

(19-12-2017 03:56 PM)Don Wrote:  

(19-12-2017 03:55 PM)TinWhisker Wrote:  Your legs, I leave alone. Umi posts it though, watch out.

And today's post is brought to you by the word, "incorrigible"

He doesn't get any better does he - for TW incorrigible is a very ''mild'' word . Wouldn't do without him though - but don't tell him that.

You just did!
And now I said that he'll no doubt rib you some how

[TinWhisker]

Nope, his ribs are off-limits too. But Umi, now...

[ecignut]

See what I mean Rob.

[TinWhisker]

There's worse horn-dogs than me out there. In fact, I'm a kitten in comparison. I once saw a comment about a pretty lady from some dude, made me laugh. I'd never apply it to our sweet Umi (and the reality is gross) but he said "She's so hot, I'd suck a fart out of her bum and hold it like a bong hit".

So see, I'm not NEARLY all bad.

[ecignut]

That is the worst saying I have ever heard.

[TinWhisker]

I know; that's probably why I laughed. He used a donkey hybrid instead of bum, but you get the idea.

[Don]

(19-12-2017 03:48 PM)ecignut Wrote:  Hi Don - I take it the coil legs just pin under the screws. TW is about - maybe I should not have mentioned legs.

Yeah - not a difficult build. The only problem was finding some wire of high enough resistance to suit. I must get some more 0,35 and 0.42mm Kanthal. The only Kanthal I could find was 1mm (18 gauge) which wouldn't even fit in the atty.

Eventually I found some 30 gauge SS316 wire so made a simple 7 wraps on 3mm single coil (1.3 ohms measured). Then stuck it on the Wraith and put a cell in. It seems that whatever was in that bottle had turned into tear gas.

So I stuck it on the DNA200 squonker. Then tried to remember how to switch modes on a DNA mod. Now vaping some variant on custard at 16W rather nicely. The airflow will go all the way to far too tight. Had to open it up a bit to get the draw I wanted.

A small atty like that on a pretty huge DNA200 mod looks a little odd but vapes nicely.

[mike.williams]

I'm finding myself more and more interested in the single coil RDA's now that I'm planning on getting the Luna squonker being as it's a single 18650. I love my Goon OG and keep going back to it and it will do single coil and there are now 3rd BF pins for it. I'm just not sure how well it will perform in single coil mode.

[Don]

I can recommend the Airlab clone. Single coil, pretty straightforward build. (Would have been easier if I'd had some higher resistance wire but the Kanthal fairy appears to have stolen it. I have nickel, titanium in all sorts of sizes, SS316 and 316L in a wide range of sizes but the only Kanthal I can find is 1mm in diameter (18 gauge)). As long as you want to do MTL.

Single coil drippers are hard to wick badly. While it can be done, it isn't easy.

The Origen little is a good MTL RDA as well

[mike.williams]

(19-12-2017 09:46 PM)Don Wrote:  I can recommend the Airlab clone. Single coil, pretty straightforward build. (Would have been easier if I'd had some higher resistance wire but the Kanthal fairy appears to have stolen it. I have nickel, titanium in all sorts of sizes, SS316 and 316L in a wide range of sizes but the only Kanthal I can find is 1mm in diameter (18 gauge)). As long as you want to do MTL.

Single coil drippers are hard to wick badly. While it can be done, it isn't easy.

The Origen little is a good MTL RDA as well

Yeah that's the thing Don. I'm a DTL guy. Just can't get the satisfaction from MTL. I don't need huge clouds but need at least restricted DTL. I run the Goon OG wide open.