What did you get today?

[BOB]

sorry Michael im way to busy at work at the moment to make another pipe
have a look under the diy bit there is a thread that tells you how to make one
if you break it down into sections and take your time its  not that hard
basically its drilling a few holes in a bit of wood
if you decide to make one give me a shout I will help as much as I can  

[Michael]

Thanks mate, I might do that. I wonder if there's a way to put the button on the side of the bowl, to make it feel more natural when holding it... I'll have to start in the "drawing and planning stage" lol

[BOB]

I got the mutation rda today
it seems to be really well made and everything fits snug
the post hole screws and 510 are smooth
the well will hold a lot of juice and the post holes are huge
the adjustable airflow is not to stiff and not to loose
I haven't had time to build it yet and have to go out somewhere
hopefully I will build it later tonight

---

all for 20 quid

[Don]

(23-09-2014 08:59 PM)Michael Wrote:  Thanks mate, I might do that. I wonder if there's a way to put the button on the side of the bowl, to make it feel more natural when holding it... I'll have to start in the "drawing and planning stage" lol

That wouldn't be so easy. The magnetic button switches work very well - you just have to be a bit careful about lining up the copper pipe.

And while 22mm copper pipe is standard stuff here it almost certainly isn't in the US where it would probably be 25.4mm (1") or 3/4" (19mm). One would be too loose for an 18650 and the other too tight.

[Michael]

What a coincidence, Bob, I picked up a Mutation X today too! I brought my wire rayon and tools with me so I built it in the shop after they boiled it for me. My build was .19ohm using side-by-side wire, 7 wraps on 2.4mm, dual coil. It's a bit more airflow than I'm used to, but I'm loving it great flavor and cloud production with 98% PG juice. The deep well made tons of room for me to stuff my rayon under the coils, so it lasts a lot longer between drips than my Patriot or TOBH. All in all, it reminds me of the McDonald's theme: badum-ba-ba-bum, I'm lovin' it! 

I also picked up a Caravela clone. I'm really liking the button, since my other mods have recessed buttons. The problem I've had with it is that I can't get my atty and battery to fit flush with it. I might file down the contact screw to make it work. Still, seems like a nice mod. 

I got both the atty and the mod for 60 bucks after tax and all, so I'm pretty happy with my cheap and good purchase. The vape shop guy even threw in two flavors of juice with it. 

[Spasmod]

great stuff guys.. that's a proper cloud chasing atty too so should be quite the thing..

That would go nice on your Morse Box-Mod Bob

[BOB]

It will be going on once I have built it spas
both batterys are charged and I have some 0.5 kanthal and some cloudy juice at the ready
I am going to my mates house tonight he has one of those coil winder jigs and I want a play with it

[Don]

They are handy but a minor mod with a bolt, a couple of washers and a wing nut in the handle loop make them better for making vaping coils.

[Michael]

I got a Veritas RDA today. That thing has awesome flavor. Also got some 24ga kanthal, and a few new flavors. I finally jumped on the custard bandwagon with the rest of you guys lol. 

[Don]

Custard allegedly works best with silica at around 1.8 ohms. Very few custards will survive 0.2 ohm but then flavour is usually a casualty at those power levels. I tend to vape custard well above half an ohm.