Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
RDA Help
Author Message
StRaNgE KlOuDs Offline
Junior Member
**

Posts: 9
Likes Given: 3
Likes Received: 1 in 1 posts
Joined: Sep 2018
Reputation: 0
Post: #1
RDA Help
Ok guys I just bought a vandy vape mesh RDA I have the kanthal mesh strip in it with cotton bacon on my voopoo drag. I wet the cotton down and when I take a hit off it, it is burning my throat. My mod is set at 80 watts and I'm using juice that's 70/30 I also feel like I'm lacking flavor compared to my valyrian tank any suggestions ?
08-11-2018 01:26 AM
Find all posts by this user Like Post Quote this message in a reply
Chuck-Drl Offline
Resident Wiseguy
*****
FreeCycle

Posts: 3,682
Likes Given: 3,976
Likes Received: 5,946 in 2,653 posts
Joined: Jul 2015
Reputation: 133
Post: #2
RE: RDA Help
Coil resistance ?

Why be normal when wierd is so much fun.
08-11-2018 01:58 AM
Find all posts by this user Like Post Quote this message in a reply
StRaNgE KlOuDs Offline
Junior Member
**

Posts: 9
Likes Given: 3
Likes Received: 1 in 1 posts
Joined: Sep 2018
Reputation: 0
Post: #3
RE: RDA Help
My mod reads it at .13
08-11-2018 02:00 AM
Find all posts by this user Like Post Quote this message in a reply
Chuck-Drl Offline
Resident Wiseguy
*****
FreeCycle

Posts: 3,682
Likes Given: 3,976
Likes Received: 5,946 in 2,653 posts
Joined: Jul 2015
Reputation: 133
Post: #4
RE: RDA Help
Make sure the mesh is not pushe askew a portion touching the atty in the wrong spot will cause a hot spot , otherwise Try a bit less cotton . Whe you rew wick be sur you have no hot spots .

Why be normal when wierd is so much fun.
08-11-2018 02:10 AM
Find all posts by this user Like Post Quote this message in a reply
Chuck-Drl Offline
Resident Wiseguy
*****
FreeCycle

Posts: 3,682
Likes Given: 3,976
Likes Received: 5,946 in 2,653 posts
Joined: Jul 2015
Reputation: 133
Post: #5
RE: RDA Help
Just to hit all bases , which size mesh ? Micron and with

Why be normal when wierd is so much fun.
08-11-2018 02:14 AM
Find all posts by this user Like Post Quote this message in a reply
StRaNgE KlOuDs Offline
Junior Member
**

Posts: 9
Likes Given: 3
Likes Received: 1 in 1 posts
Joined: Sep 2018
Reputation: 0
Post: #6
RE: RDA Help
So I put a nickle strip in and rolled the cotton and packed under the coil before tightening the screws down now I've got an ohm reading of .07 and much smoother hits is .07 ohms safe on a regulated mod ?
08-11-2018 02:16 AM
Find all posts by this user Like Post Quote this message in a reply
Chuck-Drl Offline
Resident Wiseguy
*****
FreeCycle

Posts: 3,682
Likes Given: 3,976
Likes Received: 5,946 in 2,653 posts
Joined: Jul 2015
Reputation: 133
Post: #7
RE: RDA Help
I work a bit with mesh , i suspect he build was to low for 80w . Wire gauage plays a huge roll in appropriate watage , wile a .15 a1 24g build will vape nice at 80w a .15 a1 28g will vaporize juice faster than it can wick scorching the cotton .
Use nickel in tc mode , watage gets it to hot and it produces toxic oxides

Why be normal when wierd is so much fun.
(This post was last modified: 08-11-2018 02:28 AM by Chuck-Drl.)
08-11-2018 02:25 AM
Find all posts by this user Like Post Quote this message in a reply
StRaNgE KlOuDs Offline
Junior Member
**

Posts: 9
Likes Given: 3
Likes Received: 1 in 1 posts
Joined: Sep 2018
Reputation: 0
Post: #8
RE: RDA Help
So the mesh that came with it is
NI80
Kanthal A1
SS316L
They're pre-measured a bit long so I trim a bit off of the end insert 1 end into the platform and tighten it down, then I take a strip of cotton fold it over and then fold the mesh over it so it's good and tight then tighten 2nd clamp down. I ended up with .07ohm I'm vaping at 85 watts and it hits really good 
08-11-2018 02:31 AM
Find all posts by this user Like Post Quote this message in a reply
[-] The following 1 user Likes StRaNgE KlOuDs's post:
Chuck-Drl (11-08-2018)
Chuck-Drl Offline
Resident Wiseguy
*****
FreeCycle

Posts: 3,682
Likes Given: 3,976
Likes Received: 5,946 in 2,653 posts
Joined: Jul 2015
Reputation: 133
Post: #9
RE: RDA Help
Ok Ni80 is Nichrome not nickel , so safe in watage mode . Glad you got it sorted .

Why be normal when wierd is so much fun.
08-11-2018 02:38 AM
Find all posts by this user Like Post Quote this message in a reply
[-] The following 1 user Likes Chuck-Drl's post:
ecignut (12-09-2018)
StRaNgE KlOuDs Offline
Junior Member
**

Posts: 9
Likes Given: 3
Likes Received: 1 in 1 posts
Joined: Sep 2018
Reputation: 0
Post: #10
RE: RDA Help
Thanks guys :-) 
08-11-2018 02:43 AM
Find all posts by this user Like Post Quote this message in a reply
Post Reply