Post Reply 
 
Thread Rating:
  • 1 Votes - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Kraken Genesis Style Rebuildable Atomizer (clone)
Author Message
JohnnyMac Offline
The Mac Daddy!
********
Administrators

Posts: 1,513
Likes Given: 1,217
Likes Received: 1,317 in 683 posts
Joined: Aug 2013
Reputation: 8
Post: #1
Kraken Genesis Style Rebuildable Atomizer (clone)
Kraken Genesis Style Rebuildable Atomizer (2.5mL)

Purchased from Fasttech on 11/16/2013, shipped on 11.20/2013, received on 12/2/2013
*As always, clicking any of the pictures will open the full sized image.

Details from website:

  • Genesis style RBA
  • Airflow control system
  • 3 airfow holes located on the top cap
  • 2.5mL glass tank
  • Laser engraving logo
  • Serial number laser-engraved on the center post
  • Stainless steel protective sleeve
  • Optional single coil or dual coil setup
  • Build using mesh/silica wick and wire
  • Diameter of wick hole: 2.8mm (Approx.)
  • 22mm external diameter
  • Can be used with 510 drip tip (drip tips sold separately)
  • Comes with some rebuildable parts

PRODUCT TYPE:   Rebuildable Atomizers
MATERIAL:  Stainless Steel + Glass
COIL REBUILDABLE:  Yes
COIL REPLACEABLE:  No
CONNECTION THREADING:  510
PACKAGE TYPE:  Plain
PACKAGE CONTENTS:  1*Kraken RBA, 1*Nichrome Wire, 1*Phillips Screwdriver, 1*Stainless Steel Mesh(400)

Dimensionsus | metric

DEPTH:  22 mm
HEIGHT:  49 mm
WIDTH:  22 mm
PRODUCT WEIGHT:  69 g

Product Numbers
FASTTECH SKU:  1530400




I purchased the Kraken shortly after purchasing the Pulse-G atomiser which I reviewed several days ago.  I think it's pretty obvious why I couldn't resist the Kraken - it's incredible looks and rumored performance.  This is an atomiser that has been high on people's list since it was released.  When Fasttech finally listed it at the fantastic price of $12.92 I just couldn't resist.  A couple of weeks later it was in my hands.

Aside from a slightly bent up generic looking box, the Kraken I received was in good cosmetic condition and I only had one issue with it out of the box.  During assembly at the factory, one of the O-rings in the top cap piece was pinched and stuck in the groove.  This made it impossible to remove the end of the top cap by hand no matter how hard I tried to press it out from behind.  I was finally able to free it by a steel rod and rapping it with a hammer while holding the main outer sleeve.  Once I had it out I could clean up the shred of O-ring and clean out the stuck layer of rubber from the inside of the one groove.  After that I was able to remove and insert the end piece as intended and could even rotate it to open and close the airholes.  All was well.

Below is the Kraken and included accessories.  The Kraken comes without a drip-tip so if you don't already have one, make sure you purchase one to use with your Kraken.  The accessories included consist of a swatch of #400 stainless steel mesh (enough for several wicks), a length of NiCr wire (roughly 30awg), and a small phillips screwdriver.  Everything you  need to get your Kraken in vaping condition.

[Image: 11214603704_832df56fcb_z.jpg]

Here is a slightly better peek at the accessory bag.

[Image: 11214718953_99085cfaf7_z.jpg]

Removed from it's protective cello is the Kraken in all of it's polished SS glory.  I have to say it is arguably the best looking atomiser currently available.

[Image: 11214588555_d2d5e57385_z.jpg]

All pieces are extremely solid, thick, well machined and polikshed to a beautiful lustre.  The engraving is unusually deep and crisp.  Quite a pleasant change from the usual super shallow etching I am used to seeing these days.

[Image: 11214605656_fafe9411c5_z.jpg]

Here you can see the top section where the drip-tip is inserted.  The hole is perfectly sized for a snug fit of the tip you choose for it.  This top piece also controls airflow to one or both of the airholes in the main outer body.  By rotating the top piece you can open or close the airflow to one or two coild depending on your build and draw preferences.

[Image: 11214709303_09fbd01f55_z.jpg]

Here are the 3 main components to the Kraken.  The tank and coil head, the outer body/sleeve, and the top cap.

[Image: 11214587254_0b33f11e0a_z.jpg]

Inside the main shell with a ridge that seals to the lower tank section.  Above that ridge section is a groove that one of the O-rings in the top-cap seats into allowing the top-cap to be rotated easily while keeping it in place vertically.

[Image: 11214595606_e902e227f1_z.jpg]

Here you can see the two O-rings of the top-cap.  One sits in the groove cut into the outer sleeve and the second seals tightly to prevent any air leaks.  Three triangular air holes are cut into the wall of the top-cap.  Depending on the position of the cap you can adjust airflow through just one or both of the vertical air slits cut into the outer sleeve.  It is fully adjustable from no airflow to a very light, airy draw for you low ohm cloud chuckers.

[Image: 11214579954_bef56f1eca_z.jpg]

The coil head comes prepped for a single wick and col setup.  The hole for the second wick comes plugged with an allen head screw leaving the fill and main wick holes open.

[Image: 11214588096_5af651a9d7_z.jpg]

The glass tank slides off from the main section.  The seals are very tight and ensure there will be no leaking of your e-juice of choice.  Thanks to the glass tank you can use any juice you want without worrying about it cracking on you.  The glass is fairly thick and not delicate feeling but not as thick as the glass on the Pulse-G.

[Image: 11214561235_c5fe0e7308_z.jpg]

The original Kraken is made by Vicious Ant and costs roughly $150 USD on the street.  This version is cloned by Tobeco, I believe, and is a fairly accurate rendition down to the "ViciousAnt" logo etched into the base.  I don't own the real Kraken for 150 different reasons but looking at pictures of the real artical and comparing them to this $13 clone it is nearly impossible to tell them apart when assembled.  Internally they are nearly identical as well with the only obvious difference being the quality of the glass tank on the original but that is only visible with the outer shell removed.

[Image: 11214562144_c789564803_z.jpg]
[Image: 11214571956_934bb12156_z.jpg]

Each Kraken has it's unique serial number etched into the center stem inside the tank section.  The serial number on mine is "FV306".

[Image: 11229611215_61511c226b_z.jpg]

Threads on the 510 connection are clean, deep and well machined.  The center connection post sticks out a little further than I would care for it to but as long as the center pin on your mod is floating or adjustable you should be just fine.

[Image: 11214677673_1eee22e5b4_z.jpg]

All screws are stainless steel and all the holes are threaded well and clean.  The center post is part of the main center stem.  The two washers on the center post make it as easy to secure a coil made of kanthal ribbon as a coil of regular wire.  The holes, clockwise starting from the bottom left, are the primary wick hole, the negative post screw for the primary coil, the fill hole, the secondary wick hole, and finally the secondary negative post screw.

One thing that should be included, but is not, is an allen wrench for the secondary wick hole plug.  It would also have been nice to have some sort of plug for the fill hole.

[Image: 11214564896_48ca114f1c_z.jpg]

Here you can see the center post a little better.

[Image: 11214671433_25dda089e8_z.jpg]

Assembled, the Kraken is 22mm in diameter.  Perfect for a flush fit on most mods.  I currently only have brass mods so of course I had to order two stainless mods in order for the Kraken, and the Pulse-G, to really look their best.  I picked up a stainless steel Nemesis clone and a Poldiac clone in stainless and brass.

[Image: 11214546974_962578cc71_z.jpg]

PERFORMANCE

The Kraken was very easy to setup.  Before doing anything further I thoroughly washed all components on hot water and dish detergent to remove any machining oils and bad tastes.  I chose to use only a single coil for now accompanied by a mesh wick with a silica wick in the center.  For the coil itself I made a microcoil using 0.8mm x 0.1mm kanthal ribbon.Resistance as pictured below was between 0.8 and 0.9 ohms.  I ended up changing it out for a regular wire microcoil.  Why, you might ask? Because the damned thing burst into flames while testing it out with juice in it!  Can't say I've ever seen that before but apparently PG/VG juice can and will ignite if enough heat is applied. LOL!  Fortunately only the centerpost and coil flamed up.

[Image: 11214662093_29bb301516_z.jpg]

After the ribbon coil burst into flames I decided to go with a slightly more conservative 28AWG kanthal microcoil at 1.3 ohms.  yeah, I know I used the fill hole as the wick hole.  I liked the idea of using the unthreaded hole for the wick.  When I redo it in dual coils I will use the intended holes.  it works just fine like this so no worries there.

[Image: 11214538034_284a26a2f5_z.jpg]

Everything heating up properly with no electrical shorts and, more importantly, no flames.  Time to assemble the outer shell and give it a vape!

[Image: 11214523565_0248774caf_z.jpg]

Works a treat!  Sorry for the boring video but the taste is marvelous and the vapor thick and heavy.




I will follow up with some parting shots of the Kraken mounted on my brass King mech mod.  Looks fantastic but would look even better on a stainless mod.  Good thing I have a couple on the way. Wink
[Image: 11214767875_df3a3a4ccd_z.jpg]

She's a beauty!

[Image: 11214783066_09c2308690_z.jpg]

CONCLUSION


I can't recommend this enough!  Sure, there were a couple nigling issues but easily fixed.  it is extremely solid, well made and most of all gorgeous!  At less than $13 USD how can you NOT add this to your collection.  Performance is fantastic, and it really brings out the flavor in my juice.  The best of a tanker and a droipper combined into one lovely device.  Go and get one now!

As always, feel free to hit me up with any questions or comments you may have.  Thanks for checking out my review. Smile


Johnny Mac
06-12-2013 03:21 AM
Visit this user's website Find all posts by this user Like Post Quote this message in a reply
Spasmod Offline
Administrator
********
Administrators

Posts: 5,561
Likes Given: 8,351
Likes Received: 5,624 in 2,912 posts
Joined: Aug 2013
Reputation: 101
Post: #2
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
As usual, Outstanding review! thanks very much for sharing buddy! looks like a fantastic unit - I'm stoked for mine to arrive now Big Grin

Sorry for the Spanish inquisition on skype LOL Tongue
06-12-2013 04:03 AM
Find all posts by this user Like Post Quote this message in a reply
Spasmod Offline
Administrator
********
Administrators

Posts: 5,561
Likes Given: 8,351
Likes Received: 5,624 in 2,912 posts
Joined: Aug 2013
Reputation: 101
Post: #3
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
Quick word of warning about this Kraken clone.

After discovering a strange flavour while Vaping and after a little searching by Johnny, we found some reports of Machine Oil being found inside the chamber where the center pin sits.

Sure enough, that was the cause of the flavour issues with mine too. Just bear in mind guys that a normal wash will not remove this Machine oil.

You WILL need to completely remove the center pin from the atomizer (it presses out) and clean the inside cavity thoroughly.


I used Pure Alcohol Sanitary Hand Cleaner - just to be sure the oil had been dissolved and removed prior to reassembly (Vodka would also be a good alternative).. NOw all is good and the flavour is perfect Smile

Just thought I would bring that to the attention of any prospective buyers out there and it only takes 10 mins of your time to do
09-12-2013 02:50 PM
Find all posts by this user Like Post Quote this message in a reply
JohnnyMac Offline
The Mac Daddy!
********
Administrators

Posts: 1,513
Likes Given: 1,217
Likes Received: 1,317 in 683 posts
Joined: Aug 2013
Reputation: 8
Post: #4
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
Glad that that was the cause and it was easy to resolve.  I was pleasantly surprised to find that I had zero issues that had been reported by others.
09-12-2013 03:39 PM
Visit this user's website Find all posts by this user Like Post Quote this message in a reply
the little puffer Offline
Junior Member
**

Posts: 28
Likes Given: 0
Likes Received: 10 in 7 posts
Joined: Dec 2013
Reputation: 2
Post: #5
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
Good write up.
I doubt its tobeco tho as their wholesale price is more than double this and according to them the do no sell to fasttech
09-12-2013 11:44 PM
Find all posts by this user Like Post Quote this message in a reply
Spasmod Offline
Administrator
********
Administrators

Posts: 5,561
Likes Given: 8,351
Likes Received: 5,624 in 2,912 posts
Joined: Aug 2013
Reputation: 101
Post: #6
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
(09-12-2013 11:44 PM)the little puffer Wrote:  Good write up.
I doubt its tobeco tho as their wholesale price is more than double this and according to them the do no sell to fasttech

They told me the same.. "We do not co-operate with that seller" Big Grin
09-12-2013 11:47 PM
Find all posts by this user Like Post Quote this message in a reply
the little puffer Offline
Junior Member
**

Posts: 28
Likes Given: 0
Likes Received: 10 in 7 posts
Joined: Dec 2013
Reputation: 2
Post: #7
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
I got a formal letter the other day pmsl
09-12-2013 11:51 PM
Find all posts by this user Like Post Quote this message in a reply
JohnnyMac Offline
The Mac Daddy!
********
Administrators

Posts: 1,513
Likes Given: 1,217
Likes Received: 1,317 in 683 posts
Joined: Aug 2013
Reputation: 8
Post: #8
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
I know it's not from Hcigar either as they told me they don't sell to Fasttech either. Whomever made it their stuff is top notch.
10-12-2013 02:14 AM
Visit this user's website Find all posts by this user Like Post Quote this message in a reply
gords1001 Offline
Sir Gords - Slayer of Joose !
*****

Posts: 1,937
Likes Given: 500
Likes Received: 1,035 in 654 posts
Joined: Aug 2013
Reputation: 9
Post: #9
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
Who was the formal letter from Wayne?  Her majesties custons and excise?
10-12-2013 09:24 AM
Find all posts by this user Like Post Quote this message in a reply
madecov Offline
Senior Member
****

Posts: 499
Likes Given: 2
Likes Received: 311 in 196 posts
Joined: Sep 2013
Reputation: 4
Post: #10
RE: Kraken Genesis Style Rebuildable Atomizer (clone)
Everyone in China says they don't sell to Fasttech, but they move enough stuff that they can't be ignored. I think these disclaimers are all part of an agreement so when an importer or other dealer complains they can say "see we don't sell to them".

I have two shipments from them in process and they should be called Slowtech.

BTW, really nice set up. I may need to look at that for myself.

[Image: 1379125800_10_1_USD_5_dark.png]
(This post was last modified: 11-12-2013 04:25 AM by madecov.)
11-12-2013 04:24 AM
Find all posts by this user Like Post Quote this message in a reply
Post Reply