Threaded Mode | Linear Mode

**TinWhisker** · (10-21-2018)

All awed until I saw vendor juice!

Chuck-Drl · (10-21-2018)

Perhaps he likes that juice in particular

paulS · (10-21-2018)

(21-10-2018 03:28 AM)TinWhisker Wrote: All awed until I saw vendor juice!

Free samples TW. Have not payed for juice in years. Did not want to waste 28ml of juice I really liked until I found it didn't leak, lol. Left it on a towel overnight! Did not leak. Few issues with the tank but overall great. Can run 28ml, 18ml (preferred set up), RTA mode, series deck mode, velocity deck mode, or postless with three coils (needed to with Gently's coils, lol.)

With the 18ml tank the coils are close to your mouth and flavor is really good. Lots of airflow options. I run at around 150 watts ... and it is not too hot with the big tank. Just need good coils for sure.

Now we are currently designing a little shorter mod that will be wide enough for the 40mmm tank. I'm partnering with a French Canadian out of Quebec City who is an electrical genius. The box logo is done with 3 D printer so we can customize easier.

**ecignut** · (10-21-2018)

(20-10-2018 10:04 PM)gentlydoingit* Wrote: Well if that's not frugal nothing is!

I guess the coil is probably slightly over engendered for mtl
Does it still have the same crispness of flavour?

Hi Mike - it certainly does - I reckon another month before the wire gives up.

**TinWhisker** · (10-21-2018)

I was only funnin' with you Paul. I wouldn't turn down free vendor juice. Well, depends on the juice I guess.

**Don** · (10-21-2018)

I believe I have some coming from China.

Review in short order. Problem is juice reviews are problematic as tastes vary so widely.

Chuck-Drl · (11-12-2018)

Been toying with a new coil build i'm calling a " Beggers Cup" disigned for sampling juice , it is a vertical coil whith a few layers of carbonized mesh worked between the lower 3-4 wraps . It holds just a few drops of juice , but is adequate to sample a juice or test your own mixes . Got a few kinks to mend , but some fresh mesh and an intact pair of tweezers will help .
Incidentaly , i'm useing 22g a1 6 wraps .2 resistance at 45w. Power is not quite dialed in , with so little juice as you can imagine it's not to hard to bugger the coil.

**TinWhisker** · (07-30-2019)

Figured I'd awaken this thread with the standard coil build I do on the Profile.

The Profile is primarily a mesh RDA but I've adapted it easily to a traditional coil. The coil is a 3.5mm ID, 26ga SS316 wire, 7 wraps spaced single, set at 3.8v. To mount the coil, I leave the legs really long and mount it transverse to the deck. When tight, I then slip the coil jig in and turn it to the proper direction. The air flow holes and juice well are made for a coil to face only one way, thus the need for twisting. Mesh would align properly as intended. Also, the Profile has a spring lift under the build for the mesh cotton which is not only unneeded with a regular coil, but actually in the way. So I removed it long ago. Unfortunately, I thought of this thread after the coil was mounted, so I don't have a shot of the tall legs and transverse initial mount. Maybe next time.

Anyway, here's the build, blued and glowed, ready for cotton. Works a treat. It's basically what I've used all of 2019 so far. Topside too.

[Image: 20190728_111438_resized.jpg]

Threaded Mode \| Linear Mode How do you dip yer wick?
Author	Message